含不同形状内热源的圆管内纳米流体自然对流及换热数值研究

采用格子玻尔兹曼方法对有三种恒温热源（圆形、三角形、方形）参与的圆管内纳米流体（铜-水）自然对流进行数值研究。主要研究瑞利（Ra）数,纳米颗粒体积分数以及热源几何形状等控制参数对纳米流体的流动与传热的影响。结果发现纳米颗粒体积分数的增加有利于强化传热,且在Ra数较小时,平均努塞尔（Nu）数增加的幅度要优于Ra数较大的情况。在所研究的控制参数范围内,方形热源的平均Nu数最大。根据数值结果给出不同热源表面的平均Nu数、纳米颗粒体积分数、Ra数三者之间的函数关系式,该函数关系可为此类工程的设计提供理论指导。     

The thermophysical properties of low‐temperature Pb plasma

The thermophysical properties of low‐temperature Pb plasma are calculated at temperatures 10–100 kK and densities below 0.2 of the solid‐state value. The thermodynamic values (pressure and internal energy) and transport coefficients (electrical conductivity, thermal conductivity, and thermal power) are considered. The plasma composition and thermodynamic parameters are obtained within the chemical approach, namely by means of the solution of the corresponding system of the coupled mass action law equations. Atom ionization up to +4 is taken into consideration. The electronic transport coefficients are calculated within the relaxation time approximation. The results obtained by means of the present model are compared with the available data of other models and experiments.     

A comparison of quantitative nuclear magnetic resonance methods: internal,external, and electronic referencing

The performance of three quantitative NMR methods was compared in terms of short‐term and long‐term precision and accuracy, robustness, linear range, and general applicability. The Internal Reference method employs a reference material co‐dissolved with sample; the External Reference method employs a reference material contained in a separate solution; and the third method, known as Electronic REference To access In vivo Concentrations (ERETIC), employs an externally calibrated digital reference peak. The Internal Reference method results were the most precise and remained stable within 0.1% for at least 4 weeks. The results from the External Reference and ERETIC methods were practically equivalent to each other during this time. These methods exhibited small differences relative to the standard set by the Internal Reference method and slightly lower precision, establishing them as practical alternatives to the Internal Reference method. In contrast to the Internal Reference method, the External Reference and ERETIC methods possess several advantages that address peak overlap, flexibility of calibration, and duration of applicability. The study was designed such that each spectrum contained the information needed to compare the three methods while all other variables were kept constant. Applicability of pulse width compensation is addressed. ERETIC software compensation and minor adjustments to 90° pulse width were concluded to be unnecessary for this system. Although each of the methods was applied here to specifically calculate and compare chemical purity values, this evaluation applies generally to absolute quantitation by NMR. Copyright © 2013 John Wiley & Sons, Ltd.     

Frequency‐dependent NMR relaxation of liquids confined inside porous media containing an increased amount of magnetic impurities

Frequency‐dependent NMR relaxation studies have been carried out on water (polar) and cyclohexane (nonpolar) molecules confined inside porous ceramics containing variable amounts of iron oxide (III). The porous ceramics were prepared by compression of powders mixed with iron oxide followed by thermal treatment. The pore size distribution was estimated using a technique based on diffusion in internal fields that exposed a narrow distribution of macropore sizes with an average pore dimension independent of iron oxide content. The relaxation dispersion curves were obtained at room temperature using a fast field cycling NMR instrument. They display an increase of the relaxation rate proportional to the iron oxide concentration. This behavior is more prominent at low Larmor frequencies and is independent of the polar character of the confined molecules. The results reported here can be fitted well with a relaxation model considering exchange between molecules in the close vicinity of the paramagnetic centers located in the surface and bulk‐like molecules inside the pores. This model allows the extraction of the transverse diffusional correlation time that can be related to the polar character of the confined molecules. Copyright © 2013 John Wiley & Sons, Ltd.     

Precise Radiometry: Some Recent Aspects of Fruitful Interaction with Atomic Physics

Modern radiometric analytics demands a complex consideration of nuclear and electron shell processes, if more pretentious aims are envisaged. As an example the small variation of decay rates of radionuclides presents possibilities for information on chemical situations of decaying atoms. In principle this phenomenon is well known since many years, but now the situation is such that, e.g. in ^99mTc internal conversion, a full agreement of the difficult experiments and the respective theory was established. The secondary emission of X-rays as a consequence of high excitation of electron shells in combination with nuclear transitions supplies another example for a methodical progress of radiometry. Investigations on ⁵¹Cr as an electron capture nuclide have shown that chemically induced variations of the K_α to K_β X-ray intensity ratio is at least qualitatively understood.     

优化端点条件的平面二次均匀B样条插值曲线

在利用反求法构造B样条插值曲线时，往往需要选取端点条件。 因此，可对端点条件进行优化选取，使得构造的B样条插值曲线满足特定要求。提出了一种利用曲线内能极小选取平面二次均匀B样条插值曲线端点条件的算法。首先给出了二次均匀B样条插值曲线分控制顶点与首个控制顶点（即端点条件）的递推关系式；然后给出了利用曲线内能极小优化选取首个控制顶点的算法，证明了利用该算法构造的C¹连续二次均匀B样条插值曲线为保形插值，并通过数值算例证明了算法的有效性；最后，为便于实际应用，基于MATLAB平台设计了算法所对应的图形用户界面，用户通过简单的操作即可获得光顺的C¹连续二次均匀B样条保形插值曲线。     

Degradation of a polyester‐urethane coating: Physical properties

In this article we studied the evolution of thermomechanical properties of a polyester‐urethane coating during degradation under different degradation conditions, i.e., aerobic and anaerobic conditions with and without dry/wet cycling during degradation. Dynamic mechanical and thermal analyses show that under aerobic conditions the coatings become stiffer and more brittle in the glassy state. This stiffening is probably due to the increase in the amount of hydrogen bonding and the formation of oxidized groups which increase the polarity of the material and enhance the interactions of the polymer segments. However, oxidation reactions result in a considerable decrease in cross‐link density and stiffness in the rubbery state. Both changes, in the glassy and rubbery states, give rise to development of internal stresses. These stresses increase as the degradation process proceeds. Nevertheless, for samples exposed to anaerobic conditions, the stiffness remains constant in the glassy state and the cross‐link density slightly increases as a result of degradation. This reconfirms the dominance of the effect of oxidation reactions on the mechanical failure of the coatings. Oxygen permeation measurements show a more‐or‐less time‐independent diffusion coefficient and a gradual decrease in solubility of oxygen as a function of exposure time. This results in a slight decrease in oxygen permeation (mainly in the early stage of the degradation) as degradation proceeds. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 659–671     

Tutorial review on validation of liquid chromatography–mass spectrometry methods: Part II

This is the part II of a tutorial review intending to give an overview of the state of the art of method validation in liquid chromatography mass spectrometry (LC–MS) and discuss specific issues that arise with MS (and MS–MS) detection in LC (as opposed to the “conventional” detectors). The Part II starts with briefly introducing the main quantitation methods and then addresses the performance related to quantification: linearity of signal, sensitivity, precision, trueness, accuracy, stability and measurement uncertainty. The last section is devoted to practical considerations in validation. With every performance characteristic its essence and terminology are addressed, the current status of treating it is reviewed and recommendations are given, how to handle it, specifically in the case of LC–MS methods.